PVoutput - seems to stall? - requires PVoutput donator mode

craigcurtin · December 8, 2021, 10:58pm

Bob,

I am trying to reload historical data with my IOTAWATT.

I am chewing off one month at a time

If i start with the current month - all seems to work OK and it catches up after a couple of hours and i see todays data (and the rest of the month) show up in PVoutput

However if i go back and try and load (say) the previous months data - it starts off fine and after a short period of time comes up with a message saying

Transaction rate limit exceeded - resuming at xx:yy (usually two hours time) - however it never seems to recover from there and continue on

When i look at the logs i see this (excerpt - there is a lot more)

12/08/21 23:00:39 PVoutput: Reload status beginning 11/01/21 00:05:00
12/08/21 23:02:18 PVoutput: Transaction Rate-Limit exceeded. Resume at 00:00
12/09/21 00:00:18 PVoutput: Unrecognized HTTP completion, upload Bad request 400: Missing parameter [data
12/09/21 01:00:18 PVoutput: System DeepwaterRoadCastleCove - NSW, interval 5, freeload mode
12/09/21 01:00:19 PVoutput: Reload status beginning 11/01/21 00:05:00
12/09/21 01:02:01 PVoutput: Transaction Rate-Limit exceeded. Resume at 02:00
12/09/21 02:00:01 PVoutput: Unrecognized HTTP completion, upload Bad request 400: Missing parameter [data
12/09/21 03:00:01 PVoutput: System DeepwaterRoadCastleCove - NSW, interval 5, freeload mode
12/09/21 03:00:02 PVoutput: Reload status beginning 11/01/21 00:05:00
12/09/21 03:01:42 PVoutput: Transaction Rate-Limit exceeded. Resume at 04:00
12/09/21 04:00:42 PVoutput: Unrecognized HTTP completion, upload Bad request 400: Missing parameter [data
12/09/21 05:00:42 PVoutput: System DeepwaterRoadCastleCove - NSW, interval 5, freeload mode
12/09/21 05:00:43 PVoutput: Reload status beginning 11/01/21 00:05:00
12/09/21 05:02:22 PVoutput: Transaction Rate-Limit exceeded. Resume at 06:00
12/09/21 06:00:22 PVoutput: Unrecognized HTTP completion, upload Bad request 400: Missing parameter [data
12/09/21 07:00:22 PVoutput: System DeepwaterRoadCastleCove - NSW, interval 5, freeload mode
12/09/21 07:00:24 PVoutput: Reload status beginning 11/01/21 00:05:00
12/09/21 07:01:59 PVoutput: Transaction Rate-Limit exceeded. Resume at 08:00
12/09/21 08:00:59 PVoutput: Unrecognized HTTP completion, upload Bad request 400: Missing parameter [data
12/09/21 09:00:59 PVoutput: System DeepwaterRoadCastleCove - NSW, interval 5, freeload mode
12/09/21 09:01:00 PVoutput: Reload status beginning 11/01/21 00:05:00
12/09/21 09:02:39 PVoutput: Transaction Rate-Limit exceeded. Resume at 10:00
12/09/21 09:18:40 PVoutput: Transaction Rate-Limit exceeded. Resume at 10:00

I have tried to use the Stop button and it does not seem to respond

Any ideas about how to tackle this ?

Also the defintion

Craig

overeasy · December 9, 2021, 12:22am

Is it possible that either toy consumption or solar goes negative? Can you plot them?

craigcurtin · December 9, 2021, 12:44am

Solar would go negative at night yes - the inverters are setup to remain online and hence draw a small amount of power - however if i do the current month (December) it loads fine and continues on

Consumption no - as it is where all my house loads are

YOu can see in the PVoutput graph below that is has picked up December each day (and the first few days were done in batch mode)

Craig

overeasy · December 9, 2021, 3:16am

You can only upload 14 days history in freeloader mode. You need to donate at least $15AUD to enter donator mode where you can upload 90 days worth of history and also there is a mich higher rate-limit that allows a lot more and larger uploads each hour making uploading a lot of history faster.